vArranger Forums

@Phiet
Most current audio interfaces are multiclient. The M-Audio 610 is a somewhat older audio interface, the latest driver is designed for Windows 8. It's quite possible that the M-Audio 610 isn't multiclient. I don't remember if it is. Check how many ASIO drivers the M-Audio 610 provides, and if there are multiple, try to addressing different ASIO pairs for each application. It might work.

Try vArrangerSynth on SD1000 mode.

Quote from: haweneu on July 03, 2025, 06:26:59 AMAre there vst Instruments in the market that Play with 1 ,,MIDI Noten on,Off" a Audio-samplechord in Major, Minor..?

Yes, if we're talking about VST instruments, for example NI Kontakt. There are not Midi Processing script but scripts for NI Kontakt. We've developed scripts for Kontakt where you don't just press a specific key, it then triggers major, minor, etc. That's the easiest way, many VST instruments can do that. Much better, this script for NI Kontakt recognizes the chord you've played with your left hand and immediately plays the real (sampled) chord. It doesn't matter if it's major, minor, 7th, 6th, dim, etc., it plays the real audio chord. In short, it recognizes the fingered chord and plays the audio chord that's sampled in NI Kontakt at a specific octave.
And not only that, but also via velocity switch you can create different variations of audio chords, fast or slow strumming, short or long chords... etc. Prerequisite is that all these chords are available as audio chords in instrument from NI Kontakt. Not only with NI Kontakt, you get the same thing with other VST instruments but this time with MIDI Processing Script.

Below is a picture where you can see what happens when you play, for example, a C-minor on the left side in vArranger² and how the played chord "calls" the audio chord that is in "minor Octave" on a certain key. This happens thanks to the script mentioned above.

Quote from: haweneu on July 02, 2025, 07:16:10 AM...But this is not the Same as with Ketron Event with Real Audio Tracks for Drums, Bass and Chords, special for Rythm Guitars. This uses for Guitars sampled chords as Audio Base and play then this in some Variations Like Major, Minor, Seventh  ...... For this you need much more Audio Samples for all Chord Variations!

I use the V3Sonority soundmodule for playing sampled Guitar chords with my Midi accordion. This has separate midi notes for Major, Minor, seventh and dimishned chords! And this function cannot used with VA2! But it Sounds much better than an Midi triggered Chord with 4 separate Guitar samples...

That's exactly what the TRANSAUDIO WA-L2 does. There are several VST MIDI plugins, VST instruments, and even MIDI processing applications that use scripting, which makes it very easy to do exactly what you can do with, for example, a V3 Sound Sonority or Accordion Master XXL and a MIDI accordion or a whole series of Ketron keyboards. This means there aren't just three, four, or five MIDI notes, but audio cords or audio Loops in various octaves for major, minor, seventh, dim, etc., which are then played when major, minor, seventh, or other chords come from the style in the vArranger, and in terms of audio loops, they are synchronized with tempo by vArranger². It's a bit better than with Ketron keyboards, especially with fill-ins, where Ketron still has a few little problems. The scripting mentioned above, is very powerful and can do almost unbelievable things.

My mistake, it was in German.

Quote from: haweneu on June 28, 2025, 06:08:23 AMHi,
I understand! I use VA2 with my WERSI Spectra (with diy switches and potentiometer for VA2 in Front of lower manual = See attached picture) as Masterkeyboard and an Asus Vivo Pc Core i5. Sounds only generated with SD1000 and V3Sonority XXL Hardwaremodules. You Wrote in your picture of TRANSAUDIO WA-L2 that VA2 Play Audio Loop Styles. But VA 2 cannot Play this Type of Styles like Ketron Event, or I am wrong?

Mit freundlichen Grüßen
Werner

TRANSAUDIO WA-L2 uses only a software sound engine. In addition to Dan's fabulous Genos 2 sound bank, there's also a large SF2 sound pack (over 15GB of samples) and various VST instruments. Only the best computer hardware configuration will suffice (the latest Intel Ultra 9 CPU series, 5TB of the fastest Gen5 NVM storage with 14,000MB/sec, 96GB DDR5 PC6400 memory). The operating system is a Windows 11 64-bit audio system, configured down to the smallest detail for audio. The audio interface is also very "fast." This is the only way to operate with minimal latency (0.7ms or 1.4ms), which is a must for live gigs. vArranger plays styles similar to any other hardware keyboard, only with more useful features. However, the Arranger has nothing to do with audio loops, it's the same with hardware keyboards. That's the responsibility of the Sound Engine alone. A style is simply a group of short MIDI sequences that play note on/off, MIDI controllers, and SysEx data. As mentioned, sound engine, in this case VST instrument, are responsible for the audio loops. vArranger is a fantastic software arranger that does its job flawlessly; it just needs to be used correctly and to its full potential.

Quote from: nakeyer on June 30, 2025, 05:22:42 PMWow! Now - can you make something like that with GigLad arranger ?

Until vArranger gets a style editor, you can use a software Yamaha style editor. The best style editor I've ever used is "StyleMagic YA". We have Giglad and it is a software still under development and isn't quite ready for live gigs.

Quote from: haweneu on June 28, 2025, 06:08:23 AMHi,
I understand! I use VA2 with my WERSI Spectra (with diy switches and potentiometer for VA2 in Front of lower manual = See attached picture) as Masterkeyboard and an Asus Vivo Pc Core i5. Sounds only generated with SD1000 and V3Sonority XXL Hardwaremodules. You Wrote in your picture of TRANSAUDIO WA-L2 that VA2 Play Audio Loop Styles. But VA 2 cannot Play this Type of Styles like Ketron Event, or I am wrong?

Mit freundlichen Grüßen
Werner

TRANSAUDIO WA_L2 nutzt nur software Sound Engine, neben den Dans fabelhaften Genos Sound Bank, da ist noch ein grosses SF2 Sound Pack (über 15GB samples) und verschiedene VST Instrumente. Nur das besste Computer hardware konfiguration ist gut genug (die neueste Intel Ultra 9 CPU Reihe, 5TB schnellsten NVM speicher Gen5 mit 14.000MB/sec, 96GB DDR5 PC6400 Arbeitsspeicher). Operative System ist ein Audio Windows 11 64Bit speziell bis zum kleinsten Detail, für Audio konfiguriert. Auch Audio Interface ist sehr "schnell". Nur so kann es mit kleinsten Latenz (0,7ms bis 1,4ms) gearbeitet werden, was für Live Gigs ein muss ist. vArranger spielt Styles änlich allen anderen hardware Keyboards, nur mit mehr zehr nützlichen Funktionen, aber Arranger hat nichts mit dem Audio Loops zu tun, das ist genau so bei hardware Keyboards. Dafür ist nur Sound Engine zuständig. Ein Style ist nur eine Gruppe kurzen Midi Sequenzen die Noten On/Off, Midi Controller und SysEx daten abspielt. Für Audio Loops sind, wie gesagt, Sound Engine in diesem Fall VST Instrumenten, zuständig !!! vArranger ist ein fabelhafte software arranger der ohne kleinsten Fehller sein Job macht, nur es soll richtig und voll ausgenützt werden.

Quote from: nakeyer on June 30, 2025, 05:22:42 PMWow! Now - can you make something like that with GigLad arranger ?

Bis vArranger ein Style Editor bekommt, kann es ein Software Yamaha Style Editor genutzt werden, übrigens der besste Style Editor den ich unter händen hatte "StyleMagic YA". Wir haben Giglad und haben ausführlich getestet, es ist Software noch im Entwicklung und ist, vor allem, für Live Gigs, nicht reif genug.

I wrote that TRANSAUDIO WA-L2 can play Audio Loops (and Styles from vArranger2 with Audio Loops) !!!

It has the last version of vArranger². I am a Premium User all this years (50€ pro year) to be always up to date with the last software version, and it is full normally by the most software producers. TRANSAUDIO WA-L2 is one "Kraftpaket" with most powerful and last generation of CPUs, memory and storage, on specially configured Audio Windows, what is the most important thing for one Windows based musical instrument. In one word, it is one musical instrument (not computer) for professional use on stage or in studio.

Buy software and be happy !!! vArranger² is one very professional program, not a joke and this prehistorical  version 1.16 is maybe 1/16 from actual version. How to explain to you what's wrong with your configuration with ASIO4all drivers and vArranger², when this version 1.16 has only little bit structure and functions from actual vArranger² ? vArranger² is so complex, stable and good, that we make hardware Workstation and Arranger based on vArranger². It is the newest project:

Have you installed your License.reg ?

Ich vermute, du besitzt nicht lizenzierte vArranger² software, deswegen kannst du nicht auf all das zugreifen.

Wo hast du alle diese Songbooks and Sheets gesehen, hier auf Forum oder... ?

Bitte keine Intrigen verbreiten, er ist da und Ich hatte gerade heute nachmitag Kontakt mit Dan.

Dan is very well and in "ON" state. Don't spread intrigue, please !!!

No Laptop !!!

Yessss !!!

SysEx to make Midi Channel 9 to Drums Part on Ketron SD1000 is:  F0 26 7B 0F 00 08 01 F7

Quote from: Atakiss on December 21, 2019, 11:59:32 AMHi!
A little funky for Christmas!
Happy Holidays!
https://dl.dropboxusercontent.com/s/jz7e6u2da3v1rfx/FUNKY%20ATA.mp3?dl=0

https://soundcloud.com/trans-audio-aae/funky-1

...and other played from Trans Audio SF Sound Bank on vArranger² :

https://soundcloud.com/trans-audio-aae

Quote from: eallan on July 24, 2023, 02:14:22 PMAgaton ,
Could you please start a thread about how you use Loops with vArranger?
Would be very interested in how you make Audio Loops Styles and
what Plugins etc you use.

This is a little bit complex. You need one external VST Host like Cantabile, and one good VST Looper. Before I start thread about using Audio Drum Loops in vArranger² I shall upload some Clips about it. Audio Drum Loops brings much live feeling and Groove in a Style. They are no more sterile like Midi Drums. They will be synchronised with tempo of Style in vArranger² and by change of Style Parts inclusive Fill-Ins, Audio Drum Loops play 100% like a normal Midi Drum Tracks. You can start Variations, Intros, Fill-Ins and Endings when you want, it will be played without any brakes or disturbance.

But there is now too much talk about VST3 !!! It's OK, some plugins are only in VST3 format, and there will be a vA² update with this feature soon, but it's really not so, that you can't play without VST3 support. You know exactly how I do that there is currently no hardware arranger that can keep up with the range of functions of the vA², not even the new Ketron Event, provided you have a PC with sufficient power and you can assemble the VST Instruments sound engine. It goes as far as it is possible to provide all arranger tracks with audio loops that adapt perfectly to the tempo and can be played without any glitches or dropouts. Much better than Ketron Event makes it. You just have to use the right plugins and you get almost a real band on the stage, since all the accompaniment comes from audio loops (drums, rhythm guitar, bass...). I've been working almost exclusively with Audio Loops Styles for quite some time. In the end, if you only need to implement a VST as VST3, there is the already mentioned Blue Cats PatchWork that does it perfectly.

Vrsion 2.6

You can use Blue Cat's PatchWork VST in VST Host for all VST3 Plugins and it funct perfect.

You cannot view this attachment.

One of the best Midi Pedals is Roland FC300. It is one luxus Pedal but it is perfect to work with vArranger² and in a same time also with one of Roland Midi V-Accordeons (or with Bugari-Evo Haria Accordeons).

You cannot view this attachment.

I am so blind and very, very slow. I hate this questions: I have ver. 1.16 (crack) can you send me a "new version" bla... bla... bla... and at the same time I don't look how old is the post. Mea culpa, mea maxima culpa.

You have to buy vArranger² !!!

It is very easy.

You cannot view this attachment.

That's right !!!

Use conventional MIDI from your Korg PA700.

Wenn du den vArrangerSynth als 32Bit installiert hast, dan kann es sein das Korg Midi Driver 64Bit nicht erkannt wird. Probiere den vArrangerSynth als 64Bit zu installieren.

CPU, Arbeitsspeicher wieviel und welche, storage (M.2 oder konventionelle SSD), Mainboard... ? Für professionellen live vArranger arbeit mit massiven VST Instrumenten und Effekten Benutzung ist ein wirklich hochpotenter Hardware und Software System nötig. Unten kannst du CPU PassMark eines Trans Audio Systems sehen der auf der Büne mit niedrigsten möglichen Latenz von 32 Sample Buffer (0,7ms) arbeitet, somit es ist mindenstens zweimal schneller als ein Top Hardware Arranger. Für sowas ist Hardware, aber genau so viel, Software Konfiguration (Audio Windows) verantwortlich. Dabei ist das ganze (Trans Audio) sehr klein für so eine überwältigende Performance (25cm x 17cm x 11cm) samt einem Touch Screen auf dem vArranger² zu sehen ist. So ist das Gerät eigentlich ein Arranger Modul mit über viertausend besten VST Sounds und Effekten gepackt. Du kannst den PassMark Program free downloaden um Performance deinen Computer zu messen.

Link:
https://www.passmark.com/products/performancetest/download.php
Lade ersten von Links !!!

Quote from: Akkordeonhansel on January 05, 2023, 04:32:14 PMHi

I strongly playing with the thought to get into vArranger, yet I wait for the newest version.
How long to wait for that vArranger3?

Cheers
Stefan

The latest version is excellent and you don't need to wait for the next version.

Es ist alles machbar, vorausgestzt du hast entsprechende Computer hardware.

Alle UAD Audio Interfaces sind von vArranger unterstützt, nur die müssen auf 44.1kHz eingestellt werden !!!

All VSTs can be configured to receive Midi events with or without some additional Apps (Host in Host VST Plugs).

Es ist nicht ganz einfach, aber du kannst es schaffen. Alles was du wissen must ist auf dem Video unten. Dafür brauchst du allerdings ziemlich potenter Audio PC. Übrigens, alle Style Tracks (ausser Guitar) sind von VST Instrumenten gespielt.

Correctly !!! No comments.

Not for Live use !!!

Try Contour ShuttleXpress.

In this case PRESONUS STUDIO 24C. It will be fast enough for live play of VST instruments but it also depends from your Computer.

You need one Audio Interface with very fast ASIO (at last about 4-6ms Latency) to play normaly VST instruments. How many inputs you need on Audio Interface. Ketron SD1000 need two inputs and if I understand you good, you have also one DAC that you want to implement in the whole system. In this case you need one Audio Interface with at minimmum 4 inputs. Than Presonus AudioBox iOne is not good choice. Presonus AudioBox iTwo will be also not OK, but one Motu M4 will be one of the best choices for you. The price is higher, but quality is very good (Motu M4 use one of the world best ADDA: Sabre32Ultra). Motu M4 has 4 inputs in a best sound quality and its Latency is very, very low. As nearfield monitors one of the best choices price/quality is JBL 305 MKII.

In this price segment maybe: Presonus AudioBox iOne as Audio Interface and for respectable homestudio nearfield monitors you have to pay some more money.

Audio Interface ASUS Xonar U7 MKII:........................... NO
- cause no ASIO Driver and it is to slow to play VST instruments in a real time.

Audio Monitors Edifier R1600T III:..............NO
- cause it is a HiFi ware, not for using in homestudio

Ich habe dich jetzt wirklich nicht verstanden !!! Welche NI Instrumentenliste ?
Es gibt Trans Audio Sound Engine auch im NI Kontakt Format wenn du an diese
Sounds dachtest. Ich habe dir vorsichtshalber schon komplette Soundliste der
Trans Audio Sound Engine in NI Kontakt Format an PM gesendet. 

Quote from: Dan on December 24, 2021, 02:48:13 PM
It is related to dispatching the virtual instruments to use the different cores of the CPU
Have good hopes for the next week

Very, very good, one of the most important functions !!!

For the best sake I don't understand so many posts about vArranger² update. vArranger² is, as it is now, by far the best arranger software on the market without any competitor to time. In actual version vArranger² has so many functions nearly as much as no other hardware arranger. It can be arranger, it can be workstation, it can be synth, midi player, audio clip player... and most importantly, vArranger² is stable like a stone. Please, a little more patience, I am shure, the next version will be really new "sweitzer knife". Let's let Dan work !!!

And what is the command DefaultStyleVolume for Ketron Styles ?

MOTU 2408mk2 & 424 is full multiclient ASIO audio interface. All Motu's interfaces are multiclient ASIO, don't worry.

Quote from: drepalla on April 05, 2021, 07:08:34 PM
...Would this work while using another host for my VST plugins?

Which Audio Interface you use ? It must be multiclient ASIO !!!

Yesssss !!!

...and than much better cause of a huge Sample ROM of V3 Sonority XXL (4GB Raw Sample Content).

I have tested V3 Sonority XXL with vArranger² in "SD1000" Midi Mode, and V3 Sonority XXL can receive all vA² commands
from "Drum Mixer" for any Drum peace (Level, Pan, Efx, Pitch...) same as Ketron SD1000 make it. Only one problem by
V3 Sonority XXL in "SD1000" Mode is that it has some delay by Style change. It can be that some SysEx commands cause this
delay. V3 Sonority XXL react also on commands from vA² Effects for SD1000 !!!

In the vArranger² version 1.19.12 is all OK, no error masages more.

We made Instrument Definition File for newest "V3 Sound Sonority XXL".

Quote from: Nikomedia on October 17, 2020, 03:34:03 PM... I will open a case on PayPal and get my money back, because nothing what was promised happened. With the screenshot I will send to PayPal, I am sure they are on my side, as they always have been until now...

What was promised and not happend ?

Make one Instruments Bank in Kontakt and load your instruments in this Instruments Bank (max. 128 sounds).
Now you can make your Presets in vArranger and save it (Program Change Nr.).

A few Style Demos from Trans Audio Style Pack (at all about 250 Styles), played from Trans Audio Sound Engine on vArranger²:

Bis es neue Update kommt, definiere die beiden Files (vArranger² und vArrangerSynth) als erlaubt in Defender.

Excellent !!!

Quote from: pwevarranger2 on August 22, 2020, 05:03:28 PM
...Yamaha Steinberg YSUSB_V203_Win.exe driver and is incredibly low in latency (5-20ms)...

Incredibly low latency is to time much lower: 1.5ms; 3ms, or by the best Thunderbolt  Audio Interfaces 0,7ms.

Master Effekte die ich benutze sind unten zu sehen und für VST 32Bit in VST 64Bit Umwandlung gibt es
als bestes zu Zeit, schon erwähnte jBridge Applikation.

Quote from: GM on August 05, 2020, 01:13:52 PM
I am more than happy with a well-known hardware solution.

Very well, than stay by your hardware solutions. All here try to explain to you that this software has so much functions and it is so complex, powerful and better than most of the best "hardware solutions". If you don't trust in us, simply don't ask.

@Soundman

Fast alles was du möchtest kannst du in vArranger² bekommen, und weiter, es spricht nichts dagegen das du beide Applikationen parallel benutzts und dabei komplettes Cantabile aus vArranger² per Midi Befehle kontrollierst !!! vArranger² kann sehr wohl als reines Workstation fungieren, aber auch als Arranger und Workstation gleichzeitig und nicht nur als reines arranger software.

Yessssss  !!!

Only one more s*** sound expander, nothing we've not heard !!!

He asks how to send Start/Stop Command Midi Control to vArranger²,
from his "MidiMaestro"-Midi System built in his Accordion.

Ich habe dir ein post über "My Messages" geschrieben.

Wenn es um beste Lösung geht, dann Roland FC300. Es ist
teuer aber sehr funktional und logisch aufgebaut.

Es sind mehr als genug Sounds im GNS Sound Bank. Wen so viel z.B. verschiedene Piano Sounds da sind, und trotzdem nicht genug sind, dann es ist kein Problem des GNS Bank. Viel Piano wie man unten sehn kann, und da sind E-Pianos nicht mal erwähnt. Aber, das ist bei weitem nicht alles... da noch viele Piano Sounds auf einem anderem Platz untergebracht sind (die, bedingt durch Genos Soundstruktur nicht nach GM/XG Standard platziert sind).



Es sind alle wichtigsten Sounds für Yamaha Genos Styles da (Mega Voices & Co.) und alle kann man auswählen auf den Rechte "Sund Balken". Die "Sounds a la Creme" die Genos so besonderes ausmachen sind unter "EFFECT EFX" Sounds untergebracht,  die zum Teil, kann man sehen und auswählen nur wen man eine von Style Tracks aktiviert hat (Mega Voices), das auch sinn macht (wozu braucht man sonst z.B. einen Mega Voice Sound, den ist unmöglich als normalen Sound zu spielen) und dan obendrauf viele, viele andere "normale" Sounds die auch bei Auswahl Right und Left Tracks zu sehen sind. Es gibt insgesamt 261 solche Sounds (unter "EFFECT EFX"). Die Sounds sind alle im MSB=8 Bank und verschiedenen LSB Banken (wie auch in Genos). Im Sound Editor des vArrangers2 kann man mit  MSB/LSB und PCG jeder Sound im beliebigen Style auf einer Style Track oder Solo Tracks wählen und dann speichern.







Und da sind z.B. auch Super Articulation Sounds und irgendwo zwischen vielen anderen Super Articulation Sounds ist auch die schon erwähnte und viel ersehnte SA Golden Trumpet:

Superior Drummer 3 work very fine in vArranger² as VST Host.

How much RAM have you in your Computer ?
Update Kontakt to actual version !!!

Genau so ist es !!! Wen noch Fragen auftauchen, ruhig fragen.

You need to set Faders on Novation Launch Control XL on Midi CC#7 for Volume
(every of 16 Midi Chanels), than Midi CC#10 for Panorama on first line of Pots,
the second line on Midi CC#91 for Hall,  and third Line on Midi CC#93 for Chorus.
Configuration for Volume (on Faders) and first Line (of Pots) for Pan is Factory
default.

Als erstes brauchts du NI Kontakt VST Instrument. Den würdest du in einen
vArranger² VST Rack Slot einfügen. Dann machts du ein Instrument Bank
im Kontakt mit adäquaten Midi Kanal. In einen Kontakt Instrument Bank kann
man 128 Sounds laden wo dann auf PCG Midi Befehle von vArranger² auf den
angestellten Midi Kanal entsprechenden Sound abrufen, ohne Ladepause, genau
wie bei Hardware Instrumenten. Es geht alles sehr leicht und schnell aber dafür
brauchts du ein ziemlich guten Computer, mit sehr guten CPU dann mit viel, viel
Arbeitsspeicher und schließlich schnellen M.2 oder SSD Plate. Nur dann kannst du
ganz entspannt mit dem Kontakt oder anderen beliebigen VST Instrument in
vArranger² arbeiten.   

You can hear here a few Style Demos on vArranger² played from
TA Sound Bank. I shall write to you on your privat Messages here
on the forum.

In TA Sound Bank are all Ketron SD1000 melody sounds (512),
all Drum Kits (and much more) and all original SD1000 Audio Drum
Loops (Live Drums). Additional, there are over 100 multilayered
first quality class sounds from real acoustic instruments over the
world. Here some demos from Styles in vArranger² played from
TA Sound Bank:


Bluegrass


Blues


Dixieland


Funky


Gospel


Kramer


Salsa



More on:
https://soundcloud.com/trans-audio-aae

 In the Top of this site from left to the right you can see: "Home", "Help", "Search", " Profile", "My Messages"... click on the "My Messages" and you will see all what you need.

Don't split the keybard, cause vArranger send Chord, right and left sounds Midi events on Midi Channel 1(in "normal" modus). You don't need most from usual functions of masterkey when you use vArranger (transpose, split...) cause vArranger make it much better for every sound (right and left). You can use controllers from your key, it will be useful. Go to Sound Editor to see how much controls you can use for every sound and save it all with Sound or/and Style, it is much more as by any masterkey. vArranger is also very good workstation with many, many controllers.

Private Message or here "my messages".

Genos Factory JazzFunk Style with Dan's vArranger² Genos Sound Bank on Trans Audio instrument !!!

https://youtu.be/3mb6Q-DuWdk

It is one of amazing funktions of vArranger². If you use two Keys
are automatically all Right (1,2,3,4) sounds on first Key, and all
Left (1,2,3) sounds on second Key. So you have two independent
Sounds simultaneously.

@josclaes

You have PM.

Ok, very good !!!

Diese vier erste Sounds werden so abgerufen wie die nach dem editierung gespeichert werden.
Das heist wenn ein Sound von den Midi Out 2 kommen soll so speichert man es als User Sound.
Dann wird es auf einen von vier erste Plätze (My Sounds) gezogen (drug & drop), und am ende
wird alles als Song (Style) gespeichert. Taste "LINK" soll aktiviert sein wen man will das diese
Funktion greift. Das ist das ganzes Prozess.

Which VST PlugIns you use in vArranger

Go to: http://www.jmelas.gr/motif/es/bundle.php and download
MO6/8 Pack. Install this Editor and you will become one VST
instrument which you can use also in vArranger to change or edit
MO6 sounds. Attention, your MO6 must be on latest firmware.
I shall try to find Instrument Definition for your MO6.

Ich mag Opas... obwohl ich bin auch nicht im Lebensfrühling, nur 61, aber das ist mein Job,
mein Beruf und Berufung. Ich werde helfen wann immer ich kann.

Yesssss, Dan has answered to you, additional will be very good if you have MO "Instrument Definition"
and copy it to: "vArranger2\vArrangerData\Sounds\INS for better sounds of MO6 to find, or change.

Quote from: Woge1000 on September 26, 2019, 05:07:00 PM
Bei mir sieht das offt so aus beim Style wechseln.Rechts alle Sounds weg.
Ich muß Neu starten und alles ist wieder da.

Da sind wir wieder bei dem "Song speichern" Window. Da sollst du beim
"Right/Left Hand Sounds" kein hacken setzen. Dan bleiben die sounds unberührt !!!




Styles oder Songs die du schon unter aktivierten "Right/Left Hand Sounds" gespeichert
hast, sollst du wieder speichern aber dieses mal ohne hacken.

...and how can it be after disabled ? With edit from .sty2 data or ?

Jaaaaa es funzt, ich habe gerade mit .png Format probiert !!!

Bingo !!! Obwohl auch da steht .txt .rtf und .pdf,
mit .png habe ich nicht probiert.

Leider so ist es, aber eine Datei in .PDF Format umzuwandeln dauert par Sekunden !!!
Damit muss man leben.

@Livio5
Ja da hast du Recht ich habe mich auf ältere Yamahas keys bezögen wo Registration
noch nur noch mit dem sounds zu tun hätte, was auch viel mehr Sinn hatte. So wie so
sind die hardware Keys alles anderes geworden nur nicht spielbare Musikinstrumenten.
Grotten schlechte Sounds, noch schlechter Keyboard (Tastatur), mit Haufen von  ganz
unnötigen Funktionen... usw...
Trotzdem ist beim vArranger² eine fabelhafte Möglichkeit gegeben alles als Song Book
(oder Song) in unbegrenzten Zahl, abzuspeichern deswegen auch, ein separates Feld
mit Registrations tasten wäre unnötig.

@freakman
Ja, vArranger² sendet beim Sounds (Registration oder Song) wechseln, Haufen von Midi
Befehle, aber dafür wo für du es brauchts, brauchst du keine Midi Datei, vArranger² hat
eine Funktion dafür, das beim Song oder Style abrufen, kommt auch Text, Sheet oder was
auch immer du gespeichert hast.   

Das ist natürlich auch eine Möglichkeit, obwohl mit einem
hardware Midi Controller wäre eleganter.

Es wurde gehen mit einem Midi Controller der erlaubt mehrere verschiedene Midi Kontrollen
gleichzeitig zu senden. Mit so einem Controller ist kein Problem mehrere vA² Kanälen zu
aktivieren oder deaktivieren.

Ich kenne auch keine hardware keyboard das kann, oder besser gesagt,
das sich im weitesten abstand damit messen kann.

@Woge1000
Du hast im vArranger² unbegrenzte zahl von Registrationen und
daher brauchts du es nicht zu exportieren oder zu importieren. Wie
gesagt, jeder User Sound (gelbe sticker) entspricht einem Yamahas
Registration. Das kannst du an unteren Bilder sehen !!!




Das was Livio5 schrieb, da dachte er an Song Book (in Yamahas
Terminologie), wo man entscheiden kann was alles mit einem
Style gespeichert wird. Und auch zahl des Song Books ist unbegrenzt.
Siehe Bild unten.

 

Das ist bei weitem noch nicht alles. Stat 4 OTS wie bei meisten oder
besser gesagt, allen hardware Keyboards, du hast ganze 20 OTS
(in vA²: My Sounds Bar). Alle 20 kannst du, wenn du möchtest, mit jedem
Style verschieden haben, anders gesagt, immer wen du einen neuen Style
wählst kommen andere 20 sounds (eigentlich Registrationen im Yamahas
jargon). Dafür sollst du beim Style Speichern (in oberen Bild) "My Sounds Bar"
aktivieren oder deaktivieren (wenn die 20 Sounds in My Sounds Bar immer
gleich bleiben sollen). So leicht ist es beim vArranger² 

Es gibt neuerdings noch was. Du kannst, wenn du willst, ersten 4 Sounds aus
dem "My Sounds Bar" jedem von 4 Main Variationen zuteilen. Das heist, immer
wen du eine Variation wählst kommt automatisch andere Sound (oder Registration
nach Yamahas Terminologie). Wie du siehst, es ist alles so flexibel wie bei keinem
anderem hardware Keyboard. Das alles sind nur ein paar Kleinigkeiten aus, fast
unbegrenzten, vArranger² Möglichkeiten.

Daher, mein rat, vor dem Kritik oder Wünschen, immer erst fragen. Meistens ist
es schon im vArranger² implementiert.

Es ist alles schön und gut mit den PAD-s und OTS !!!
Registrations haben wir schon, ich weis nicht warum
viele User oft über Registrations schreiben. Jeder
Style kann auch eine Registration sein und jeder User
Sound ist so wie so eine Registration mit möglichen
4 Sounds (Right 1, 2, 3, 4) und jeder von dieser "Rights"
hat sein Volume, Panorama, Effect Level, Apm Envelope,
Portamento, Mono-Poly... voll unabhängig von anderen.
Was soll es noch sein ?

Quote from: garciarob on September 18, 2019, 01:23:47 PM
I think that there is a false problem. Dan asks money for intermediate updates (as a prerelease ) and not for the big update (sum of the prereleases).

Yesssssss and that is good so !!!

It is too pity to use so one powerful program like vArranger² only
as Ketron SD2 Player. Too pity !!! It is a past tense. So looks Trans
Audio system with vArranger² as Workstation and Arrangeur i the
same time. One very, very powerful sound system, with thousands
and thousands best sounds and effects !!!

If you use vA² with VST instruments, than you have the best
VST Effects on the world !!! vA² is one software Arrangeur, that
open a huge world of the best studio VST Effects to use it with
the best VST sounds. The best hardware Arrangeur is without
slightest chance towards one vA² on adequate audio-configured
machine (hardware, software and system) !!! With all new vA²
functions, which Dan make to time, it will be even much better
from day to day.

Quote from: BjayG on September 16, 2019, 02:35:47 PM


...but please don't let it lose its primary purpose and add missing things such as registrtaion menu, style auditiong, and the real time stuff etc...


Barry

vArranger² has "Registration Menu", every User Sound is one Registration !!! What is "the real time stuff", please be concrete.

Nichts zu danken, Hauptsache es funktioniert und macht dir Spaß !!!

Wenn du vArranger² als VST Host benutzts,
dann gibt es nur ein weg.

It can be also better as hardware, on very good Audio Interfaces and very
good computers. Newest generation of Thunderbolt Audio Interfaces have
Latency about 1.5ms that is less than most of hardware instruments !!!

One example:

Take Instrument Definition of S950 and increase a few
different sounds.

Quote from: Donny on March 13, 2019, 06:27:34 AM
...but the resolution from Agaton worked.
With this 1360 x 768 it is shown correct.

I know about this Bug cause I had the same problem long time ago on one
Surface and I had try with different resolutions especially cause VST Slots
Window. Actually I have known that it is a problem of Intel Graphic Card on
Surface. Single solution is to define 1360 x 768 pixels resolution. On Extern
Graphic Cards (nVidia or AMD Radeon) you can work with the best resolution
which you have.

Quote from: Donny on March 12, 2019, 08:03:22 AM
Agaton: Yes i have the resolution, but the window is only bigger (Screenshot 1920_x_1080).

Try with 1360 x 768.

Have you resolution 1920 x 1080 on Surface ?

And that is the best choice !!!

You are totally wrong with your conclusion about my "assessment" !!!
Don't write about things which are strange for you, please. My discuss
was not aborted cause Dan wrote that vA² has not internal Clock, many
apps or programs have not internal clock, but this is irrelevant cause
all apps which haven't internal clock become clock from system (Win).

It will be better naturally, but it is to many new data in a vA² and
it is not only one mapping, it will be many, many mappings if it
will be in kind of Mapping Presets. To make only one function
in vA² which user later can mapp or remap Midi notes for his
Module or software instrument(s) and save it with Style, is the
same thing. It can be very useful when implement of this function
in vA² will be not a big problem for programming or if this haven't
negative influence to whole (to time) very good stability and big
efficiency of vA². But... for both ways it will be a big job. With
one Midi processing  app like Bomes Translator, it will be not pressure
for system and it will be work hidden in a background.

Repeat, I did understand all, really all !!! Change Notes or make Remapping
for your Module, what is the problem. One of Midi Processing software
like Bomes Translator make it excellent. All good VST Drums Instruments
have a few most important Mappings, for this VST Drum Instruments you
need only to select what Mapping you will and that's all.

I understud very well your question, cause of that I had try to explain that is not
posible to make it in Drum Mixer. Drum Mixer has his other function and hasn't
any margin with Midi Note remaping. You wrote "...should not be hard at all and
you already have drum mixer...". This remaping of Midi Notes for all Modules
or Software Drum Instruments will be very, very big job and it will be very hard !!!

Quote from: bluebeat on March 06, 2019, 02:36:28 PM
At least this way it would be possible to adjust particular style drums to ANY module, software or hardware.

No, it s not possible. this commands are SysEx (or NRP/NRPR) Midi events and they are typical for
one Instrument. Many of hardware or software instruments haven't no one way to control every
Drum Note. Drum Mixer in vArranger can control Drum Notes in Ketron Modules and in SF2 Drum
Instruments (restricted).

Ich melde mich über PM. Es geht um ein SD1000 Sound Bank
mit höchstqualitativen Mutilayer Instrumenten. Da sind alle Sounds
aus SD1000 mit originalen MSB;LSB und PCG. Da zu sind spezielle
Sounds für Balkan- und Orientalische-Musik in ziemlich großen Zahl
auch da. An Drums und Percussion Sounds haben wir besonders
viel und präzise gearbeitet mit viel, viel Layers um bestmögliche
Qualität, Humanize und Natürlichkeit zu erzielen.

Es ist OK und hört sich gut, aber leider es hat auch seine dunkle Seite.
Das kann man auf jedem Sampler genau so machen aber es verlangt
viel zu viel Zeit da, mit diesen Methode muss man für jeden Tonalität
und jede Skale, adequate sounds kreieren. Es wird am ende Unmenge
Speicherplatz verlangen, besonders mit vArrangerSynth, da es alle
Samples im Arbeitsspeicher lädt und kein Sample-Streaming nutzt.
Das kommt um so mehr im Vorschein wenn ein SF2 Sound Bank grösser
und besser ist (wie zum Beispiel neueste SD1000 Sound Bank bei uns,
der um 10GB gross ist). Daher ist Midi Note Routing (die Dan im vA²
Harmony Funktion benutzt hat), bei weitem bessere und flexiblere Lösung.

Mit einem kleinem software Midi Processor der in Hintergrund läuft
haben wir alle Balkan und Orientalische Skalen, die man in dieser
Musikrichtung benutzt, schon längst gemacht. Insgesamt 7 Skalen
inklusive "No Terca". Wäre besser wenn Dan die Skalen in vArranger²
implementiert könnte, aber er hatte viel zu viel andere Prioritäten
bezüglich vArranger² zu absolvieren, deswegen müssten wir es auf
andere weise lösen.  Irgendwann wird er auch das machen. Langsam !!!

Habe beide getestet. McMillen 12 Step ist ein spezielles Controller der sich
vor allem mit Akkorden beschäftigt. Auf 12 tasten ist möglich 12 5-Stimige
Akkorden zu trigern und Softstep kann man als ganz normales Midi Controller
verwenden. Der ist besonders für Kemper Profiling Amp konstruiert, obwohl
es kann für jede beliebige Midi Controlling benutzt werden. Besonderheit des
Softstep ist das es auf allen 10 Pads a 6 Midi Controller programmieren lassen.
Beide sind sehr interessant und können perfekt mit vArranger² funktionieren.
Oben erwähnte Roland FC-300 ist aber bessere Lösung wenn es um klassische
Midi Controller geht.

Sehr, sehr gut, fast perfekt, aber auch sehr teuer Roland FC-300

Quote from: Dan on January 23, 2019, 11:29:38 AM
I will try to add it for XG so it will work with all Yamaha synth
I think MOTIF is a bit different
For the VST... I think better to go on VST Options, and SAVE a PRESET... But still need to add recall of presets with song....

Yamaha Motif is not XG Standard Instrument, cause of that your add for XG instruments
will not work with Motif. For VST Instruments it will be realy the best choice to implement
"Recall of presets with Song or/and Sound".

Drum Mixer Controllers are based on SD2 and SD1000 Sys Ex commands and
this commands understand only SDs. But, with one of software midi processor or
Midi Event Router it can be "translated" to f.E. NI Kontakt sampler in which you
can address MIDI Commands to any Note. It is a big and long job but it will be
funct like on SD2 or SD1000.

Quote from: busborg on December 11, 2018, 03:10:51 AM
Hi there. I'm playing a psr s950 which I bought as a replacement for my old roland g 800.
But must admit the 950 sounds sterile in style compared to tyros4 which is 950 big brother.
the solo sounds are good but not the sound of the styles
Thinking about trying vArranger2 with my old g 800 as the midi master keyboard.
But which sound module is to be trusted.
Ketron sd 2 or sd 1000 or maybe roland sonicell.
Hope you can help me a little before I'm buys the vArranger2 and a sound module.
Regards Busborg from Denmark

You can also use sounds from your old G800 if you want, but Sound Engine from
Ketron SD1000 is very, very good, much better as sound from G800.

Yesssss, please !!!

Than you have to go to General  / Midi Setup, and check very carefully everyone
item. It is recommended that you try with conventional Midi cables to connect
Montage with your computer, cause it is not strange that USB to Midi driver is not
always the best choice. Yamaha is not the best producer of USB to Midi Interfaces.
Simply try to see the result. The first my suspicion is Midi connection or Midi processing
between Yamaha and comp.

It is anyone "kosmetic" problem, it can be fixed very fast. Montage must change sounds so fast like it do that on commands from buttons on its command table. If you have Instrument Definition for Montage, copy it in vArranger folder, it will be helpfull for Bank and PCG on Montage This issue which make latency can be find.

Das kann in die hose gehen. Nämlich FR3X sendet konstant
Expression Befehle, jede Bewegung des Balges sendet menge
Expression CC# Events und dann ist deine Musik sehr "Pitch"
hin und her reich. Weiter, dein FR3X hat Pitch Controller, und
der sitzt in oberste Bass reihe (dafür must du es im Setup nur
einschalten).

Maybe, but only maybe, it is the problem with SysEx.
Try to filter SysEx on Yamaha Receive MIDI and check it.
Yamaha has its "specially rules" on MIDI Transmit and
Receive, it can be reason for this latency. This SysEx can
make MIDI Overflow on Yamahas.

I read very, very properly, every word... but you !!!
Anyway, please be patient.

No agaton is not quite, agaton have much to do in this time,
(a few bigger projects in the same time). Don't write that about
what you don't know anything. I don't play little bit with music,
music is my job and I must work. I have downloaded your Style,
(it is probably Roland Style) but I had no time to make it, I promise
I shall make it for you, cause you are so persistent and so boring,
and sometimes also ironical that I can't read it more. Please be patient,
it is not so danger and urgent. No atom bomb is on the way to us.
 

I understand. In this case (I know that vArranger² record perfect in tempo, whole time)
it is one of more issues in your Windows System, that must be corrected or on other way
configured. Like I wrote on the beginning of this thread, the problem can be in Audio
Windows configuration, and I know now that is definitely so. You can trust me, vArranger
make no mistake with tempo, its midi tempo is very stable !!! I send to you one picture
where vArranger² synchronize stand alone NI Kontakt on 131 bpm. Whole time (2 or 3
minutes) Tempo display on Kontakt shows values between 131,00 and 131,07 bpm. This is
optimal value on Midi Clock synchronisation. Later I have recorded in same time one Style
in vArranger² and the same audio signal from vArranger Main Out in a Studio One 4. Than,
after recording I have imported audio file recorded in vArranger² on one stereo audio track
under the recorded track in Studio One 4, and both tracks were absolutely in sync whole time
(no progressive latency in a time, no latency between this two tracks at all).

So, it is one or more issues in your system, maybe also .ini file of vArranger² (this is also part
of system), maybe a few positions in Win Sys which have to be changed to play audio, maybe
you have one AntiVirus program instaled and Antivirus programs are the worst enemy of audio,
maybe your internet LAN is guilty, it is also not the best friend of audio. It can be any of them
functions that make you problem with synced audio files. The best way in so one case, to find
the cause of problem is exclusion principle because I don't know your hardware and also software
configuration. It will be solved but it can lasts some more time. If you whant to solve this problem
than please write specification of your computer, or if it is one Laptop than write Model, and write
also which Windows you have instaled, than if you have Antivirus instaled. For the beginning it will
be enough.


You wrote often about BIAB. Which version of BIAB you use, and also which version of Cakewalk you
use. Cakewalk is one of DAWs which can be synched via Midi Clock (some versions of Cakewalk Sonar),
all other big DAWs are without this function, they synced on other ways (MMC... etc). That means that
you can try one test recording with synced Cakewalk (slave) from the vArranger² (master), to see whats
happen (if your audio interface can do it). This can help me to solve the problem very fast.

Why ? Why will be recorded audio file from vArranger out of sync ? The same
you can say about any other DAW software. Why only vArranger², what is the
difference ? In vArranger² you can define Tempo like in any other DAW, 105 bmp,
131 bmp, 178 bmp... it is no matter. The same you can do in any other music
software like Cubase, Sonar etc... you can also define the same tempo like in
vArranger², same in Africa , China or Australia.
Audio in vArranger is fixed on 44.1kHz and this can't be changed, like on some 
other DAWs, that means that your Audio Interface must be also on 44.1kHz.

I don't understand what is the problem, you write confuse. Cause of that I wrote to
you, try to explain this problem one time more but detailed and precise. What you
whant to become, or what is your target to do ? Maybe I shall help you if I know
that.

This is not the secret for Dan, he know that as programmer who implement  this function in vA2 before long, long time: vArranger send continious Midi Clock thru Midi Out Ports to external Midi periphery or internal Midi Aplications. So you can synchronize vArranger2 as master  with any DAW or VST HOST which "understand" Midi Clock !!! Naturally, vArranger recorded all what you hear from its Main Outputs, and  that is not in sync with any referent Clock cause it can be only Master and that is the  fact.

@Bluebeat

It is OK Bluebeat, no matter. I had say or write, what can be the problem, I have said
that I am not sure, but one of this things what I wrote must be "guilty" (operating system
configuration, maybe also computer hardware, or audio interface). I shall make this video
in a real time that you can see that all funct and all with this "fabulous tempo" is OK when
system and hardware are OK. We shall see all, only be patience and you will see also.

Quote from: olivier71500 on November 23, 2018, 09:39:09 AM
@Agaton
Hi ,
You wrote ".... computers are with bad Audio Win or both audio interfaces are shit ...."

What do you mean by "bad audio win" ? Do you mean audio drivers ?

No, or... not only. Bad audio Windows means that this Windows system isn't configured for audio. There are many Services, Registry,  many Apps etc. what have to be erased, deactivated, configured to make this Audio Widows better or best for audio job.

Quote from: olivier71500 on November 23, 2018, 09:39:09 AM"both audio interfaces are shit" : What are for you good and bad audio interfaces ?
Is there special specifications to take care or is it for you only "build quality" ?
Olivier

Quality of Audio Interfaces AD/DA converters  is very, very important, but it is only one reason. It is
also important what kind of audio Interface it is: USB, FireWire, PCI, PCIe, Thunderbolt, than it is very important
how much occupied one Audio Interface whole system (also in idle), than how stable are ASIO Drivers, are ASIO
Drivers Multiclient or not, can it be synced with other audio device periphery via Word Clock or any other sync
way, has it DSP-s (for Mixer and Effects) or not... etc... etc... Cause of all this differences between Audio Interfaces
you can buy one for 20 € or for 5.000 €. It can be much more written about Audio Interfaces. It was one short and
global overview.

Bluebeat don't write that about what you have not enough knowledge and experience.
That what you have attached shows just what I wrote !!!
Files what I send to you are both 131 bpm but you can't use and see that, and this is
your problem. What you doing, how did you import this audio files, which mistake you
made, I don't know but, one time more, both audio files what I send to you are 131
bpm, that is a fact !!!

You may don't trust anything what I write and what I send to you about your issue.
I have no more mind to explain it again, cause of that we make so: I shall record video
file of all what I doing in real time and... cause of the result of all what you will se later,
please be carefull with your words !!!

Quote from: bluebeat on November 22, 2018, 10:56:47 PM
ok, Agaton. Instead of saying nice things about my computer and interfaces, can you upload MP3 record from VA of style I posted using your Ta Sf2? (not Kontakt), SF2 bank, please.
Thank you.

I have posted it, and not only file recorded on vA, also File recorded in the same time on DAW.
Yo don't read carefuly !!! Tempo in vA of this Blues Style was 131 bmp. Check it !!! I have posted to you
also picture and you can see that both audio files are 100% sync.

One time more the Link:

https://we.tl/t-FFECfo1nfi


I said always "nice things" about "nice" devices !!! This can be my or not, if
it not OK is, than I can not lie only cause it is my, or your, or... I have not any
"Close Encounters of the Third Kind" with audio interfaces, devices, computers. It
is only some metal and some plastic !!! I have said to you what I have to say
about problem with latency, you can trust on it or not, this is your problem !!!

One of new Styles for vArranger² which are made only with Audio Loop Tracks.
Drums, Percusions, Bass and Accoustic Rhythm Guitar in this Style are all Audio
Loops (no Sliceing, but Elastic Audio) !!! This make possible to change Style Parts
without any disorders, disturbances, crackles etc... Change of Style Parts are like
by normal conventional Styles without Audio Loops. To change to  any oder Style
part you don't need (like by some other arrangers with Audio Loop Styles) to wait
measure end, it can be changed in any moment. Simply it is like three real musicians
on the stage, with all little, but natural human musicians artefacts and original Groove
of rhythm, with huge live feeling.

Quote from: bluebeat on November 22, 2018, 08:52:53 PM
I have tried onboard card AND 2 Asio interfaces, Wasapi and Asio, 2 different computers.Different ASIO buffers. I did my homework

That means only that both computers are with bad Audio Win
or both audio interfaces are shit. If you and me have the same
vArranger2 and you have problem with sync and i haven't it by
very very hard test... what is the conclusion ?

I made for you the hardest test in a sync domain !!!
I had recorded in a same time audio from vArranger²
and in a DAW. This is the hardest situation for one
system, two differnet aplications (programs) record
in a same time the same audio, Here are both files.
Test it !!!


Link:

https://we.tl/t-FFECfo1nfi


...and no, I am in right.

Quote from: bluebeat on November 22, 2018, 07:48:26 PM
Agaton, for testing purposes.
Here are VA style file with chords (2 files) and MP3 105 BPM drums.
See if they are in sync after 20 seconds of playing.

Drums look perfect in DAW. Outputed VA WAV starts to have latency after 18 seconds and continues stretching that latency (or clock) or whatever it is called.... coming late.

Yes, you become Latency, and difference be always more and more. This is very well known problem by bad audio cards or bad audio system configurations. 
This is a reason for all your problems. All audio cards or devices become one System Clock in your computer and other periphery, this Clock must be stable but
it is  sometimes, by bad audio hardware, or bad audio computer configuration, very unstable !!! Result of this unstable audio system is just this latency that be
constantly biger and biger with the time. I don't know which audio interface you have or you use only internal sound card with ASIO4All Driver, and I don't
know how good or worse is configured your Windows for audio. There are also another devices connected on your computer that can be "guilty" for this problem.
It can be solved but I need to know all about your hardware and software what you use. I say it one time more, it is known problem and nothing new in audio domain.

I said "seems to", I don't know what make problems on your system
but without detailed analysis we can't find what is the reason for this
big BUG. How you can see, vArranger recorded file stay in tempo perfectly
in Studio One DAW as imported audio file, thats mean vArranger recording
very good. Your problem is definitely not vArranger recorded file.

Quote from: bluebeat on November 22, 2018, 05:55:07 PM
Agaton, I am using TA SF2 bank, no VSTS.
I just tried your way and used predefined tempo of one style that was 112 BPM in VA, outputted one from BIAB of 112 BPM,
They are not synced. So predefined or not it they are not in sync.

It is no matter if you use only TA SF2 or only VST or both.
They must be synced when your Win system is good configured and your Audio Interface do its job properly.
On the picture you can see how good synced stereo wav in vArranger² recorded file with same (predefined) tempo
in Studio One. I have marked some of places intentionally in the middle of the recorded file imported in Studio One. It is
amazing how good in time it is.




It seems to be that BIAB has a big problem with export of audio or with sync. !!!

It is true, there are NO LATENCY, absolutely NO LATENCY !!!

I can Argument this with various facts, from recorded audio track in vArranger² and than
imported it in one DAW (Studio One, Cubase, Sonar...) with predefined tempo of Style what
I recorded with vArranger². This track has exactly the same tempo in DAW !!! I can record
(video) when you don't trust. I sync. v.E. one external VST Host with NI Kontakt inside synced
with vArranger² Midi Clock and tempo on Kontakt varies about 0,1 bpm what is not to hear.
Under is one picture with opened vArranger² and stand alone Kontakt (not as VST in vArranger²).
You can see the tempo is the same. Kontakt is synced over Midi Clock from vArranger² !!!
Something other you make wrong !!!

Quote from: Brzzy566 on November 07, 2018, 07:43:48 AM
Please send MI demo of this software.
I want to buy it but I don't know how it works
Thanks

No Demo version !!! vArranger² hasn't Demo Version. No fear, it is the best
Arranger at all (hardware and software), with amazing functions and many, many
things about what, top hardware arrangers kann only dream !!! There are lot of Demos
on the Net about and with vArranger². You will see and hear all what you need to know
about vArranger².

Omniverb ist ein VST Effect Plugin, und den kannst du nur in FX1, FX2, FX3
und Audio In FX importieren, aber nicht in Instrument VST PlugIn Rack !!!
Auch im FX1,2,3 VST Slots musst du etwas im jBridge Settings nachjustieren,
wie auf dem Bild unten und dan funktioniert es !!!

Update in Beta version is very, very stable, new functions are amazing and
funct 100% OK. All "hard" VST instruments which had a little problems in a
previous version are now totaly compatibile. Very, very good job Dan !!!

[OK]

OMB isn't application which can be compared with vArranger² !!!

Quote from: Dan on October 06, 2018, 08:05:51 PM
The question is.... how fast it will be when changing sounds or songs.... depending on the VSTi

By Synth VSTs the change will be currently. By Hypersonic 2 too. Sample Streaming
based VST instruments like NI Kontakt, will be not usable for Live, but... but... by Kontakt we have
one choice, to make Instrument Banks and than changing of sounds will be also currently. By VST
Instruments like Omnisphere which has "Live Mode" is the same procedure like with Kontakt
Instrument Bank. So, all in all, most of VST instruments will be ready for Live use.

You have to edit this Style in one of Yamaha Style Format Editors
and in every Style Part to set Bank and PCG events for sounds which
you need to be changed in this Style Parts. vArranger² will change
this sounds in a Style parts in a way how you edited it.